How to Install a Ghost Immobiliser
Ghost immobilisers protect your vehicle from key cloning and hacking. It works by preventing the vehicle's engine from starting until it is activated using PIN codes that is up to 20 characters in length.
This extra layer of protection isn't visible to thieves who may not expect it. Certain systems come with an app which allows the owner to disable their immobiliser if they forget their PIN number or use the service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser, a cutting edge security system, can be incorporated directly into the ECU of your vehicle. It is a subtle protection against thieves. It is extremely efficient and user-friendly, making it a valuable addition to your vehicle's security arsenal. However, just like any other anti-theft device, it's not 100% reliable and requires regular maintenance to ensure its operation. Fortunately, this guide can help you get the most benefit from the Ghost 2 Immobiliser.
CAN (Controller Area Network) is a robust serial network that allows microcontrollers to communicate with each other in short distances, without the need for central control units. It is designed to allow multiplexing of electrical wiring in vehicles to reduce copper usage and offers a range of advantages, including low costs and easy use.
In modern vehicles, the CAN protocol is used to communicate with various systems, including the engine management system (EMS) steering module, transmission controller as well as air conditioning controls and many more. It also transmits sensor data like inputs and speed sensors, to control the various functions of the vehicle. The CAN bus can be used to monitor the health of these different components. It can prevent the vehicle from starting when it is in danger of failure.
It is important to understand how the CAN bus works and how it's secured. It is possible to add new features to a vehicle by using CAN bus, however it is important to protect it from hackers and other threats. Installing a firewall, and monitoring your CAN-bus using software is the best method to accomplish this.
Ghost2's control device is hidden inside the dashboard or wiring harness, which prevents a thief from physically tampering it. It is also impossible to reset the PIN code or emergency code without access to the vehicle.
You can turn on Transport Mode if you need to give your vehicle away for valet parking, service or for any other reason. This feature disables the Ghost immobiliser's ignition and keyfob functions, and will only come back on when the vehicle is speeding at 31 mph for 15 minutes.
How to create a PIN code
The Ghost immobiliser shields your vehicle from thieves. The cutting-edge technology uses an PIN code to shut down the engine and prevent it from starting without the proper code or an authorized fob or mobile device. The system's discrete design makes it unnoticeable, and also provides unbeatable protection against theft. The system is TASSA certified and can save you significant amounts on your car insurance.
During installation, Ghost enters a "learning mode" to record the sequences of buttons that are pressed to create your unique pin codes. The installer will guide you through activating the system once the pin code is created. Once activated it will Ghost system will disable the motor that starts your vehicle until a valid pin code is entered or the vehicle is switched to transport mode. This makes it very difficult for thieves to duplicate or hack into your vehicle's start system.
Installing a Ghost immobiliser is straightforward, but it is important to follow the precise instructions in the user manual to ensure that it operates properly. Basic hand tools can assist in making accurate connections, and a multimeter can aid in checking electrical values. Insulation tape and heat shrink tubing can shield the wire from damage, while cable tie-ups are crucial to keep everything neat and secure. Be certain to test the system on a regular basis to find any issues or potential errors.
Once the installation is complete after the installation is complete, you must make a final test of the system prior to turning on the ignition in your vehicle. The Ghost immobiliser will be able to rearm itself after a period of 3 to 30 seconds, based on your vehicle model. The system is also fitted with a Service/Valet Mode that lets you temporarily disable the system to service or valet parking.
Ideally, the immobiliser should be hidden under the dashboard or on the steering wheel. Use a small amount of duct tape or paint on the wires of the CAN H and CAN L to make them easier to find during testing. The CAN H and the L wires should be connected to an electrical source that can provide an uninterrupted 12V. It is important to check the connections again after testing because an the incorrect identification of these wires could cause the system malfunction.
Activating the system
A ghost immobiliser prevents your vehicle from starting until you press a sequence of buttons inside the vehicle, usually the steering wheel, door panel or central console. The sequence is decided by the user and can be altered as needed. Once activated, the system cannot be turned off. This is a fantastic option for those who want to safeguard their vehicle against theft.
The system is designed to be undetectable, meaning it can't be detected by modern diagnostic tools or code-grabbing technology. It also does not send out radio frequencies, which makes it even difficult for thieves to find the device.
If the device is identified, it will stop the engine from running and sound an alarm that is loud enough to scare away the thief. The device can be used to track the location of a vehicle and assist in the recovery of the vehicle if it was stolen.
Contact Car Specalist Customs for a quote or to discuss your options if you're interested in Ghost immobiliser. We are certified to install ghost immobilisers in your vehicle. We will make sure that it is hidden in an area that is difficult to reach. We can also install additional security measures, such as the kill switch and wheel lock to keep your vehicle safe from theft.
Disarming the system
If you own a Ghost immobiliser installed to your vehicle, it's important to know how to disable it. It can be used in case you forget your keys or your battery dies. The system uses an unique PIN code that only you are aware of. It won't be able to start the vehicle without this code. Pressing a combination buttons on the dashboard or steering wheel is the easiest way to enter your code. This is a lot easier than using a key fob. It also keeps others from copying the remote.
Unlike some aftermarket immobilisers that require cutting wires to install, Ghost2 is non-invasive and integrates with your vehicle's CAN bus network to operate. Its main characteristic is its ability to bypass the engine without affecting the normal functions, making it hard for thieves to make use of signal boosters or copy your car keys. It doesn't emit radio frequency, therefore thieves are unable to detect it.
ghost immobiliser near me comes with a Transport Mode which allows you to temporarily disable the security system for occasions like transportation or servicing. This feature is a great option when you want to lend your vehicle to someone without sharing the PIN code or in case you want to keep your vehicle secure while driving it. Press the button five times within two seconds to enable Transport Mode. The Ghost system will confirm activation via 5 indication signals.
After you're done, make sure to save the emergency code in a secure place away from your vehicle. If you ever find yourself locked out of your vehicle You can call the technician or the company that installed the system and they'll give you the code. If you are unable to reach them You can always try to contact an authorized dealer however this will require verification procedures and could incur additional costs.
This system isn't just useful, but it will also protect your vehicle from theft, and also reduce insurance costs. Many insurance companies offer lower premiums or financial incentives to install this anti-theft system.